In an alternate world, Ethernet took on the role of the universal serial bus, and we have laptops that charge via PoE, but only possible on one of their ports (the others are usable for peripherals --- with protocols running over Ethernet too, of course.) But the same confusion regarding power and speed capabilities exists.
dale_glass 2 hours ago [-]
We'd have to invent a new connector first. It's too thick for modern laptops, not to speak of cell phones.
Also, RJ45 is terribly fragile if you keep plugging and unplugging it, eventually that latch will break. And copper can barely support 10G and is terribly power hungry when it does that. And the cables get thick and inflexible.
somat 35 minutes ago [-]
The 8 pin modular connector as found in most ethernet does have several sins but it has one huge redeeming feature, A feature I wish was found in every cable. It is easy to field terminate. Have fun putting a new end on nearly any other cable.
tlb 16 minutes ago [-]
Field termination is necessary when the connectors are too large to pull through a conduit. But if they were USB-C sized, you could just pull fully assembled cables.
It would help if computers / phones had an easy way to just identify a cable when you plug it in. Is this hard to do or just something normal people never care about?
Probably can't tell you anything about the other end of the cable though.
> Is this hard to do or just something normal people never care about?
If i believed in conspiracies i'd say the usb consortium or mafia or whatever it's called is pressuring software developers to not display that info. Otherwise they'd have "normal people" with torches and pitchforks at their door.
nerdsniper 21 minutes ago [-]
The cable can report what it "thinks" it is, and in fact, modern USB-C cables do this: they have "e-Marker chips" inside the plugs which communicate with whatever they're plugged into and enumerate their belief as to their capabilities. The thing is, manufacturers can set the e-Marker chips to spew lies, or a cable that used to support 80Gbps got slightly damaged after 6 months of use and now only reliably transmits 10Gbps.
Power capacity is relatively easy to measure ad-hoc via voltage drop from one end to the other...USB-PD controllers already do this and can even fine-tune the voltage to make sure that if the device receiving (sinking) power needs 20V they'll send 20.4V or 20.9V to compensate for voltage drop so that the charging device gets 20V on its end.
But actual maximum data throughput is hard to know. The only way to really "know" how much data can flow through a cable is with an expensive oscilloscope or cable tester. Because 80Gbps cables run at ~13GHz so, at minimum you need a 26GHz scope (Nyquist–Shannon sampling theorem) or more practically a 52GHz scope. And it turns out it's really expensive to measure electrical signals 52 billion times per second. The necessary devices start at $15,000 (cable signal integrity tester) [0] on the very low end and only work for max 10Gbps USB 3.2 cables, or past $270,000 for for 80Gbps USB4 cables (proper 60GHz oscilloscope) [1].
On the high end, each signal integrity test device can actually cost $1-2 million [2] where the base unit starts at $670,000 plus then spending additional money for hardware-accelerated analysis, specialized active probes, and the specific PAM-3 / USB4 compliance software packages.
I get that to properly test a cable, you need that level of accuracy, but for home use, couldn’t you get away with a source and a receiver that are far cheaper?
If a USB4 device can output a USB4 stream and the receiver can check that stream for errors, isn’t that sufficient?
dijit 1 hours ago [-]
it violates every products person wish to be “simple”.
There’s a reason that Windows barely shows any errors until the system fully halts.
jeroenhd 14 minutes ago [-]
Windows will throw up warnings when the disk space is nearly empty, when it detects driver instability, when RAM is full and page files can't keep up, when a specific application is draining your battery, when your files aren't backing up right, and all other kinds.
The problem with most of those is that either users don't care until it's too late ("I need to get this done now, I'll delete files later"), third party applications are the cause and Windows can't/shouldn't interfere (did a program memory leak or is the user pushing the boundaries of what the system can handle?), or because there's not much the user can do about it ("your GPU driver crashed", well gee, my drivers are up to date, let me spend half a month's wages on a new GPU then, shall we?).
The only "too late" errors I've seen on Windows are when something very important has crashed and the system needs to shut down for data integrity (crss.exe crashing on school computers comes to mind, though I doubt that was the fault of Microsoft), or when something unpredictable went wrong, like a file ending up corrupt because of a failing hard drive or flipped bit in memory.
Microsoft actually created a dedicated screen to monitor errors and failures of all kinds (https://www.elevenforum.com/t/view-reliability-history-in-wi...) that's been around since Vista. It used to open up automatically if you clicked a popup after certain errors, but it appears Microsoft eventually stopped doing that. Going by how many "today I learned" posts I find when I look up the feature, I'm guessing nobody who actually understands what the screen does ever used the feature.
ohnei 36 minutes ago [-]
They now have the option to silently add this kind of detail to logs and have clippy find answers to why is my computer odd/slow only when asked. For a long time I felt like companies leaving product decisions to the Occamist (or the closely related lazy programmer) was a superpower to compete against larger organizations that usually don't, but we may get a run for our money from emulated simplicity.
sandworm101 3 hours ago [-]
Yup. I have a work laptop that is meant to charge via USB ... But only one of the two ports will charge ... They are right beside each other! An evil trick at the office is to move someone's USB cable from one port to the other.
benj111 2 hours ago [-]
Of course there's also the issue of whether your cable is suitable and your charger suitable too.
We appear to have taken a good idea and made it shit very quickly.
jeroenhd 9 minutes ago [-]
A suitable USB cable for all features is ten times the price of a normal cable. That's why many smartphones come with USB-C cables and not actually rated Thunderbolt cables.
If the USB forum enforced their specifications, everyone would be complaining that their cables are now ten times the price, and people would still buy knock-off cables.
Same goes with chargers: I bought a 100W charger that stops delivering 100W after it overheats about half an hour into a session. I could spend twice as much on a charger that sustains the charge, but I probably wouldn't have bought that charger at all for that price.
USB-C would either be branded a bullshit expensive standard (like Apple's Thunderbolt cables are generally regarded) or an incomplete standard that gives manufacturers too much leeway.
I, for one, am quite happy that I can just buy a USB C charger now rather than spend 180 euros on an OEM replacement, even if I ocassionally need to throw a cable into the "garbage that came with an accessoire" bin.
nottorp 36 minutes ago [-]
> made it shit very quickly
What? The USB mafia has been at it since usb 1.1 or at best 2.0...
i_am_a_peasant 2 hours ago [-]
thinkpad?
isodev 2 hours ago [-]
And on top of that, Apple has that thing where only some devices can charge from their adapters. I have a special adapter just for non-Apple things because the white bricks (despite the usb-c) sometimes just refuse to give power to things. So frustrating.
Filligree 2 hours ago [-]
Mostly, that's non-compliant devices. Doesn't make it work any better, but I wouldn't assume Apple is doing it wrong here.
USB-C ports aren't allowed to provide power until after configuration, but a lot of USB-C chargers provide 5V regardless. This is wrong, but it does mean you can use a dumb C-to-micro cable which doesn't include the necessary electronics. (A pull-down resistor at least.)
And of course there's no way to tell by the looks of the cable.
josephg 1 hours ago [-]
Yeah this is right. I bought a cheap wireless mouse, with a USB-C port for charging. None of the USB-C chargers in my house would charge it, so after awhile it inevitably went flat and I took it back to the shop - since it was faulty.
The guy in the shop plugged it in to a USB-A port via a cheap A-to-C cable, and the mouse immediately came to life. Of course. I felt like an idiot.
I didn't get a faulty unit. Whoever designed the mouse was treating the USB-C plug like a newer micro-usb port. The mouse just expected 5V over the port. They clearly didn't bother testing it with a proper USB-C charger.
I returned it anyway and got a mouse that wasn't broken.
javawizard 46 minutes ago [-]
It annoys me so much when new electronics do this because the fix is both well known by now and only requires 2 dirt cheap components on the circuit board (5.1k resistors to ground on the CC lines).
As a hardware engineer among other things, that was one of the first things I learned about interfacing with USB C. How do so many consumer devices keep getting this wrong in the year of our lord 2026?
isodev 54 minutes ago [-]
> This is wrong
I understand the technical reasons behind it, but in this case - the actual expectation is to be able to use usb-c to charge other gadgets.
dijit 1 hours ago [-]
Whaaaaaaaaat?!
Apple, somewhat famously, build their power adapters incredibly well.
If they’re not charging something my default assumption will be: that thing doesn’t support PD.
I've run into problems with Apple chargers not charging my Lenovo laptop. (I used to be an Apple fanboy, but after a MacBook Pro that required 6 repairs, I switched to Lenovo).
I've been much happier since switching to Anker chargers, works much better with my Lenovo and drastically more portable than the Apple ones. It's better able to fit certain situations where the Apple brick won't fit into sockets that are close to the ground / desk, at least not without a bulky extension cable.
A bit of snark, but don't forget the Apple charger recall:
(That said, I do think Apple's chargers were designed far better than most, and I loved that they put so much design thought into the world travel kit. Anker doesn't have the interchangeable heads, but it turns out their chargers are multi-region and a simple adapter head does the job just as well, in a smaller form factor than the Apple bricks. I still somewhat miss Magsafe as well, Magsafe 1 was excellent.)
isodev 53 minutes ago [-]
Your blind trust in Apple is misplaced :)
zombot 28 minutes ago [-]
It's even worse. The same USB-A-to-USB-C cable will either charge or not charge my iPhone, depending on where I plug in the USB-A part. But the port that won't charge my phone will happily charge my headset, using the very same cable. That kind of excludes the cable as the source of the suckage, and puts the blame on either the (supposed) power source or the phone. I've observed the same effect with other devices I wanted to charge, too. Some devices just won't accept certain USB power sources while others are more promiscuous.
applfanboysbgon 47 minutes ago [-]
> The USB situation.
> The lie.
> The gap.
> The names.
> The age.
> The trap.
> The buy.
> The truth.
> The chain.
> The lunacy.
> The cheat sheet.
Fucking LLMs have literally ruined the word "the" for me.
zombot 19 minutes ago [-]
It's not ruined, it's corrupted.
cindyllm 42 minutes ago [-]
[dead]
amelius 2 hours ago [-]
Just switch to a different brand then.
josephg 1 hours ago [-]
Are other brands any better?
Rendered at 11:10:20 GMT+0000 (Coordinated Universal Time) with Vercel.
Also, RJ45 is terribly fragile if you keep plugging and unplugging it, eventually that latch will break. And copper can barely support 10G and is terribly power hungry when it does that. And the cables get thick and inflexible.
This was on show hn only yesterday.
Probably can't tell you anything about the other end of the cable though.
> Is this hard to do or just something normal people never care about?
If i believed in conspiracies i'd say the usb consortium or mafia or whatever it's called is pressuring software developers to not display that info. Otherwise they'd have "normal people" with torches and pitchforks at their door.
Power capacity is relatively easy to measure ad-hoc via voltage drop from one end to the other...USB-PD controllers already do this and can even fine-tune the voltage to make sure that if the device receiving (sinking) power needs 20V they'll send 20.4V or 20.9V to compensate for voltage drop so that the charging device gets 20V on its end.
But actual maximum data throughput is hard to know. The only way to really "know" how much data can flow through a cable is with an expensive oscilloscope or cable tester. Because 80Gbps cables run at ~13GHz so, at minimum you need a 26GHz scope (Nyquist–Shannon sampling theorem) or more practically a 52GHz scope. And it turns out it's really expensive to measure electrical signals 52 billion times per second. The necessary devices start at $15,000 (cable signal integrity tester) [0] on the very low end and only work for max 10Gbps USB 3.2 cables, or past $270,000 for for 80Gbps USB4 cables (proper 60GHz oscilloscope) [1].
On the high end, each signal integrity test device can actually cost $1-2 million [2] where the base unit starts at $670,000 plus then spending additional money for hardware-accelerated analysis, specialized active probes, and the specific PAM-3 / USB4 compliance software packages.
0: https://www.totalphase.com/products/advanced-cable-tester-v2...
1: https://www.edn.com/12-bit-oscilloscope-operates-up-to-65-gh...
2: https://www.eevblog.com/forum/testgear/uxr1104a-infiniium-ux...
If a USB4 device can output a USB4 stream and the receiver can check that stream for errors, isn’t that sufficient?
There’s a reason that Windows barely shows any errors until the system fully halts.
The problem with most of those is that either users don't care until it's too late ("I need to get this done now, I'll delete files later"), third party applications are the cause and Windows can't/shouldn't interfere (did a program memory leak or is the user pushing the boundaries of what the system can handle?), or because there's not much the user can do about it ("your GPU driver crashed", well gee, my drivers are up to date, let me spend half a month's wages on a new GPU then, shall we?).
The only "too late" errors I've seen on Windows are when something very important has crashed and the system needs to shut down for data integrity (crss.exe crashing on school computers comes to mind, though I doubt that was the fault of Microsoft), or when something unpredictable went wrong, like a file ending up corrupt because of a failing hard drive or flipped bit in memory.
Microsoft actually created a dedicated screen to monitor errors and failures of all kinds (https://www.elevenforum.com/t/view-reliability-history-in-wi...) that's been around since Vista. It used to open up automatically if you clicked a popup after certain errors, but it appears Microsoft eventually stopped doing that. Going by how many "today I learned" posts I find when I look up the feature, I'm guessing nobody who actually understands what the screen does ever used the feature.
We appear to have taken a good idea and made it shit very quickly.
If the USB forum enforced their specifications, everyone would be complaining that their cables are now ten times the price, and people would still buy knock-off cables.
Same goes with chargers: I bought a 100W charger that stops delivering 100W after it overheats about half an hour into a session. I could spend twice as much on a charger that sustains the charge, but I probably wouldn't have bought that charger at all for that price.
USB-C would either be branded a bullshit expensive standard (like Apple's Thunderbolt cables are generally regarded) or an incomplete standard that gives manufacturers too much leeway.
I, for one, am quite happy that I can just buy a USB C charger now rather than spend 180 euros on an OEM replacement, even if I ocassionally need to throw a cable into the "garbage that came with an accessoire" bin.
What? The USB mafia has been at it since usb 1.1 or at best 2.0...
USB-C ports aren't allowed to provide power until after configuration, but a lot of USB-C chargers provide 5V regardless. This is wrong, but it does mean you can use a dumb C-to-micro cable which doesn't include the necessary electronics. (A pull-down resistor at least.)
And of course there's no way to tell by the looks of the cable.
The guy in the shop plugged it in to a USB-A port via a cheap A-to-C cable, and the mouse immediately came to life. Of course. I felt like an idiot.
I didn't get a faulty unit. Whoever designed the mouse was treating the USB-C plug like a newer micro-usb port. The mouse just expected 5V over the port. They clearly didn't bother testing it with a proper USB-C charger.
I returned it anyway and got a mouse that wasn't broken.
As a hardware engineer among other things, that was one of the first things I learned about interfacing with USB C. How do so many consumer devices keep getting this wrong in the year of our lord 2026?
I understand the technical reasons behind it, but in this case - the actual expectation is to be able to use usb-c to charge other gadgets.
Apple, somewhat famously, build their power adapters incredibly well.
If they’re not charging something my default assumption will be: that thing doesn’t support PD.
https://youtu.be/SUlNKYI07SY?is=sJ2ICaXwxCsBJiXA
https://youtu.be/rwEh4jsVew0?is=NeRD7hAk-6KABAyc
I've been much happier since switching to Anker chargers, works much better with my Lenovo and drastically more portable than the Apple ones. It's better able to fit certain situations where the Apple brick won't fit into sockets that are close to the ground / desk, at least not without a bulky extension cable.
A bit of snark, but don't forget the Apple charger recall:
https://support.apple.com/ac-wallplug-adapter
(That said, I do think Apple's chargers were designed far better than most, and I loved that they put so much design thought into the world travel kit. Anker doesn't have the interchangeable heads, but it turns out their chargers are multi-region and a simple adapter head does the job just as well, in a smaller form factor than the Apple bricks. I still somewhat miss Magsafe as well, Magsafe 1 was excellent.)
> The lie.
> The gap.
> The names.
> The age.
> The trap.
> The buy.
> The truth.
> The chain.
> The lunacy.
> The cheat sheet.
Fucking LLMs have literally ruined the word "the" for me.